Skip to main content

VISION CIVIL JE-- Success In Your Endeavor (प्रयास में सफलता आपकी)

CIVIL JE PREVIOUS YEAR PAPER -UKSSSC (SAMPLE PAPER -III)

 


1- the ratio of volume of water to volume of void is known as-

A- void ration

B- degree of saturation

C- unit weight 

D- porosity


2- In a soil flow, if the value of hydraulic gradient is m, the discharge Q is -

A- Q ∝ i

B- Q ∝ ki

C- Q ∝ m

D- Q ∝ mi


3- In a double plate butt joint, the thickness criteria of joining plate is-

A- 0.6 to 0.625 times of main plate

B- 0.4 to 0.625 times of main plate

C- 0.6 to 0.89 times of main plate

D- 0.69 to 0.72 times of main plate


4- maximum gauge distance in staggered riveting is

A- 200mm

B- 100mm

C- 75mm

D- 50mm


5- if the the liquid limit of a soil is 20% and flow index is 2% , what is the value of toughness index if plastic limit is 10%-

A- 25

B- 20

C- 10

D- 5


6- earth pressure on retaining wall per unit length is-

A- p/w

B- wh^2/2

C- w.h

D- F×A/a


7-  soil which is deposit in the bottom of lake is kown as-

A- Aeolian soil

B- Colluvial soil

C- Lacustrine soil

D- Tills


8- value of maximum shear stress in fillet weld is-

A- 108 MPa

B- 150 MPa

C- 165 MPa

D- 120 MPa


9- Bulk modulus (k) is the ratio of-

A- shear stress to strain

B- noramal stress to volumetric strain

C- later strain to longitudinal strain

D- normal stress to shear strain


10- if the weld face angle is above 90°, the value of k in fillet weld is-

A- 0.70

B- 0.60

C- 0.65

D- 0.75


11- A soil is impermeable if the particles size is varies from

A- 0.06 to 0.075mm

B- 0.002 to 0.06mm

C- 0.0002 to 0.002mm

D- 0.075 to 4.75mm


12- if τ = c + σtanΦ, soil is-

A- cohesive

B- non-cohesive

C- consolidated

D- non of these


13- values of camber various for high betumin surface is-

A- 2.5% to 2%

B- 2.5% to 1.7%

C- 2% to 1.7%

D- 1.7 % to 2.5%


14- the longitudinal beam is used in bridge called-

A- spanderal beam

B- stringer beam

C- joist beam

D- Girder beam


15- in a soil mass pressure increase upto ∆p, the impact of pressure on void ratio is- 

A- p∝ e

B- p∝ 1/e

C- p∝ e/∆p

D- non of these


16- width of steel chain varies from-

A- 6 mm to 16 mm

B- 12 mm to 16 mm

C- 10 mm to 16 mm

D- 6 mm to 12 mm


17- A 20m change use to measuring the distance of 200m, while chain is found 10cm too short. The true length measured is-

A- 201m

B- 200m

C- 199m

D- 201.2m


18- tilting of rails is-

A- 1 in 20 outward

B- 1 in 20 inward

C- 1 in 10 outward

D- 1 in 10 inward


19-no construction joint shall be allowed in low water level-

A- 60cm below

B- 40cm above

C- 60cm above

D- 40cm below


20- the diameter of iron pegs is generally taken-

A- 0.1cm

B- 0.5cm

C- 1.0cm

D- 1.5cm


21- Px =Py =Pz state that-

A- Bernoulli's

B- Pascal's

C- Kutter's

D- Franci's

 

22- atmosphere pressure at sea level is-

A- 10.34m

B- 103 kN/m2

C- 1.01325 N

D- 100 N/mm2


23- manometric fluid pressure is measured by-

A- single column manometer

B- piezometer

C- U-type manometer

D- Bourdon tube


24- aggregate used for MY grade concrete per 50 kg bag is-

A- 480kg

B- 330kg

C- 250kg

D- 163kg


25- water cement ratio for PCC M20 grade concrete in very serve condition-

A- 0.45

B- 0.50

C- 0.55

D- 0.60


26- the centre line of road is known as

A- camber

B- crown

C- medians

D- kerb


27- permissible design speed for main line track of meter gauge is-

A- 120km/h

B- 100km/h

C- 85km/h

D- 75km/h


28- Bernoulli's equation is applicable for-

A- real fluid

B- ideal fluid

C- viscous fluid

D- above all


29- shear stress diagram for a rectangular beam is-

A- parabolic curve

B- circular

C- semi-circular

D- elliptical


30-Value of P, in Lacey's canal theory is-

A- 0.705√Q

B- 2.75√Q

C- 4.75√Q

D- 275√Q


Answer key:- 1-B,2-C,3-A,4-C,5-D,6-B,7-C,8-A,9-B,10-C,11-C,12-A,13-C,14-B,15-A,16-B,17-C,18-B,19-A,20-C,21-B,22-B,23-C,24-C,25-A,26-B,27-D,28-B,29-A,30-C

Comments

Post a Comment

Popular posts from this blog

UKSSSC CIVIL JE SAMPLE PAPER

  UKSSSC SAMPLE PAPER 1- In a liquid limit test, the moisture content at 10 blows was 70% and that at 100 blows was 20%. The liquid limit of the soil, is A- 35% B- 50% C- 65% D- 60% 2- The active earth pressure of a soil is proportional to (where φ is the angle of friction of the soil) A- tan (45° - φ) B-cot2 (45° + φ/2) C- tan2 (45° - φ/2) D- tan (45° + φ) 3-An ideal vertical curve to join two gradients, is A- circular B- parabolic C- elliptical D- hyperbolic 4-The angle of internal friction of clays, is usually A- 0° to 5° B- 5° to 20° C- 20° to 30° D- 30° to 45° 5- pore water pressure is equal to- A- Total pressure-effective stress B- Total pressure+effective stress C- effective stress-total pressure D- non of these 6- minimum ranging rod required for indirect ranging is- A- 3 B- 4 C- 5 D- 6 7- throat thickness of fillet weld is- A- T= k× size of weld B- T = 0.7×size of weld C- T = 5/8× thickness of thinner member D- T = 3/5× thickness of thinner member 8- Maximum shear stress...
1 comment
Read more

AUTO-CAD AND INSTALLATIONS OF AUTO-CAD

Auto Cad is the product of Autodesk Company. The founder of Auto Cad was John Walker from California (U.S) 1980. Auto Cad generally use for Civil and Mechanical Engineering work. Advantage- there  the following two major advantage use of Auto Cad software are- User friendly nature software and very easy to operate. Available free for students through out simple registration. Profits- software working by just providing commands in various terms. Software use in the field of Civil Engineering, Mechanical Engineering and Electronic Engineering for drawing purpose of various uses. Installation Process:- Auto cad available in two kinds of installation. 1- You can Install for students version without any cost. 2- You must to need pay for Installation and getting Activation Key by Autodesk. If you will Install Auto Cad for student version, there will be some feature are not available may be because its free for general purpose not for professional. you may get this by just simple registra...
Post a Comment
Read more

COMMANDS FOR 2D AUTOCAD

whenever you have installed the Auto Cad, you must have an need to setup the dimensions first.Let's move toward the Auto Cad and open the window, type un and press the enter. you have showing window like this.....  after change the dimensions decimal to engineering and 0'0'' you need press OK.  now you need to type d enter and you see the window like this..... press the modified option and go to primary units and change here the as change above. now go to fit option and change the scale value at least 1:10,due to this your dimensions unit show to you proper size in your drawing.  this was the basic setup of Auto Cad for the drawing in feet,meter,inch,etc. you have change according to your requirements. Important Basic Commands For Auto Cad- There are the following basic commands which are very compulsory to knowing before 2D drawing in Auto Cad are-  Line Command  Flit Command  Extend Command  Trim Command  Erase Command  Copy Command ...
Post a Comment
Read more

 


UKSSSC CIVIL JE I UKPSC CIVIL JE I Previous Year Papers I Practice Sets I All Subjects I Copyright©VISION CIVIL JE.