Skip to main content

Posts

VISION CIVIL JE-- Success In Your Endeavor (प्रयास में सफलता आपकी)

UKSSSC CIVIL JE SAMPLE PAPER

  UKSSSC SAMPLE PAPER 1- In a liquid limit test, the moisture content at 10 blows was 70% and that at 100 blows was 20%. The liquid limit of the soil, is A- 35% B- 50% C- 65% D- 60% 2- The active earth pressure of a soil is proportional to (where φ is the angle of friction of the soil) A- tan (45° - φ) B-cot2 (45° + φ/2) C- tan2 (45° - φ/2) D- tan (45° + φ) 3-An ideal vertical curve to join two gradients, is A- circular B- parabolic C- elliptical D- hyperbolic 4-The angle of internal friction of clays, is usually A- 0° to 5° B- 5° to 20° C- 20° to 30° D- 30° to 45° 5- pore water pressure is equal to- A- Total pressure-effective stress B- Total pressure+effective stress C- effective stress-total pressure D- non of these 6- minimum ranging rod required for indirect ranging is- A- 3 B- 4 C- 5 D- 6 7- throat thickness of fillet weld is- A- T= k× size of weld B- T = 0.7×size of weld C- T = 5/8× thickness of thinner member D- T = 3/5× thickness of thinner member 8- Maximum shear stress for

PREVIOUS YEAR PAPER UKSSSC

  SAMPLE PAPER FOR UKSSSC CIVIL JE 1- Quantitative earthquake measurements done by ? A- F.Omeri's B- MMI C- MSK D- Richter's E- All above 2- earthquake center on earth surface is called ? A- Focus B- Pith C- Epicenter D- Focal 3- Reason to provide Built-up Beam ? A- M.O.R > B.M B- B.M > M.O.R C- M.O.R = B.M D- All Above 4- What is the error in triangular Notch ? A- 5dh/2h B- 2dh/5h C- 3dh/2h D- 2dh/3h 5- In which beam point of contrafluxure never act ? A- Propped Cantilever B- Cantilever Beam C- Simply Supported D- fixed Beam E- Overhang Beam 6- what's the correct relationship b/w E,G,K and 1/m A- E= 3G(1-2/m) B- E= 2K(1-1/m) C- E= 3k(1-1/m) D- E= 2G(1+1/m) 7- Least count of  Optical Theodolite in favour of degree is ? A- 20 sec. B- 1 sec. C- 15 sec. D- 5 sec. 8- what is correct error in Auto level ? A- E= C√mi B- E= C√k C- E= C√f D- Non of these 9- Relationsh b/w Bouyent unit weight and Critical hydraulic gradient is ? A- Ysub = Yw×Ic B- Ysub = Yd×Ic C- Ysub = Ic×Ac

UKSSSC JE (JAL NIGAM 2020) PAPER

  UKSSSC JE - JALNIGAM 2020 1- The colour of light for visibility fog is- A- Yellow B- Green C- Red D- White 2- A column of length 'L' is pinned at both the end edges. The effective length of the column is- A- 1L B- 0.8L C- 1.2L D- 2.0L 3- The fore bearing of a line is 260°. The back bearing of this line is- A- 100° B- 80° C- 120° D- 10° 4- The earth work excavation is calculated in- A- Linear meter B- Cubic meter C- Lump sum D- Square meter 5-The maximum velocity in open channels occurs - A- A little below the free surface B- at the free surface C- Near the channel bottom D- At the centre 6-one of the principales of planning is- A-The plan should not be realistic B- The plan should be flexible C-The plan should be fixed D- The plan should be shallow 7- The type of plastics used for the manufacture of domestic water supply and drainage is-  A- Polystyrene B- Acrylic C- High density polyethylene D- poly vinyl chloride 8-The number of equation to used for finding the resultant of

COMMANDS FOR 2D AUTOCAD

whenever you have installed the Auto Cad, you must have an need to setup the dimensions first.Let's move toward the Auto Cad and open the window, type un and press the enter. you have showing window like this.....  after change the dimensions decimal to engineering and 0'0'' you need press OK.  now you need to type d enter and you see the window like this..... press the modified option and go to primary units and change here the as change above. now go to fit option and change the scale value at least 1:10,due to this your dimensions unit show to you proper size in your drawing.  this was the basic setup of Auto Cad for the drawing in feet,meter,inch,etc. you have change according to your requirements. Important Basic Commands For Auto Cad- There are the following basic commands which are very compulsory to knowing before 2D drawing in Auto Cad are-  Line Command  Flit Command  Extend Command  Trim Command  Erase Command  Copy Command  Move Command  Arrow Command  O

AUTO-CAD AND INSTALLATIONS OF AUTO-CAD

Auto Cad is the product of Autodesk Company. The founder of Auto Cad was John Walker from California (U.S) 1980. Auto Cad generally use for Civil and Mechanical Engineering work. Advantage- there  the following two major advantage use of Auto Cad software are- User friendly nature software and very easy to operate. Available free for students through out simple registration. Profits- software working by just providing commands in various terms. Software use in the field of Civil Engineering, Mechanical Engineering and Electronic Engineering for drawing purpose of various uses. Installation Process:- Auto cad available in two kinds of installation. 1- You can Install for students version without any cost. 2- You must to need pay for Installation and getting Activation Key by Autodesk. If you will Install Auto Cad for student version, there will be some feature are not available may be because its free for general purpose not for professional. you may get this by just simple registration

 


UKSSSC CIVIL JE I UKPSC CIVIL JE I Previous Year Papers I Practice Sets I All Subjects I Copyright©VISION CIVIL JE.